Hatsukokoro x Nigara Yorokobi SLD Copper Damascus Sujihiki 240mm Birch Handle
Hatsukokoro x Nigara Yorokobi SLD Copper Damascus Sujihiki 240mm Birch Handle is backordered and will ship as soon as it is back in stock.
Pickup in Australia only
In Stock Now
-
Hatsukokoro Hayabusa ATS34 Sanmai Petty 150mmSale price $126.00 Regular price $148.00Unit price
-
Hatsukokoro Blue 2 Damascus Migaki Santoku 180mm Ebony HandleSale price $157.00 Regular price $185.00Unit price
-
Hatsukokoro Sumi Blue 2 Kurouchi Santoku 165mm Black Chacate HandleSale price $84.00 Regular price $99.00Unit price
-
K&S Yuepo SLD Nashiji Sujihiki 270mm, Ebony HandleSale price $115.00 Regular price $135.00Unit price
-
K&S Yuepo SLD Nashiji Gyuto 240mm, Ebony HandleSale price $115.00 Regular price $134.00Unit price
-
K&S Yuepo SLD Nashiji Gyuto 210mm, Ebony HandleSale price $104.00 Regular price $122.00Unit price
-
K&S Yuepo SLD Nashiji K-tip Gyuto 210mm, Ebony HandleSale price $104.00 Regular price $122.00Unit price
-
K&S Yuepo SLD Nashiji Bunka 180mm, Ebony HandleSale price $94.00 Regular price $110.00Unit price
Availability
Delivery unavailable for this item. Available for in-store pickup only.
-
St Peters, NSW —2 Bishop St, Unit 2, St Peters NSW 2044
Goes well with
Detailed Specifications
| Line | Hatsukokoro Yorokobi SLD Copper Damascus Kurouchi |
| Profile | Sujihiki / Slicing knife |
| Bevel Type | Double Bevel |
| Weight | 181 g | 6.4 oz |
| Edge Length | 227 mm | 8 15/16″ |
| Heel Height | 37 mm | 1 29/64″ |
| Width @ Heel | 3.1 mm | 1/8″ |
| Width @ Mid | 2.6 mm | 7/64″ |
| Width @ 1cm from Tip | 0.9 mm | 1/32″ |
| Steel | SLD | Semi-stainless |
| Blade Construction | Sanmai - Stainless Damascus Clad |
| Typical hardness | 62 to 64 HRC |
| Surface Finish | Kurouchi |
| Handle | Octagonal Birch Burl with Spacer |
| Region | Hyogo |
| Best for |
|
| Pros | Cons |
|
|
- Don't cut hard things! Japanese knives are brittle so bone hacking is a NO NO!
- Wash with neutral detergent after use, and wipe dry;
- Please don't wash knife with dishwasher, it will damage the wood handle;
- Be careful not to leave the knife close to a heat source for a long time;
- It is a lot more dangerous to cut with a blunt knife than a sharp knife!
- It is best to sharpen a Japanese knife regularly on a waterstone.
- Semi-stainless steel won't rust easily but may still patina
Knife details

Sujihiki
筋引
Slicing knife · Double bevel
A long, narrow slicer for dividing large meat; Tojiro says it cuts sashimi too.
Read more-
Hardness
Very high
How hard the steel is after heat treatment, measured in HRC. Harder steel can take a thinner, sharper edge but is more likely to chip. Typical hardness: 62 to 64 HRC
-
Edge retention
Very good
How long the edge stays sharp in kitchen use before it needs sharpening. Lab figure: 499 mm of test card cut at 60.5 HRC (D2, Knife Steel Nerds CATRA test, 2020). Hardness used: 63 HRC, the usual hardness makers sell it at.
-
Toughness
Good
How well the steel resists chipping and cracking from bones, hard boards or twisting.
-
Rust resistance
Fair
How slowly the steel rusts or stains when left wet.
-
Ease of sharpening
Fair
How quickly the steel comes back to sharp on a whetstone.
-
Sharpness
Fair
How fine an edge the steel can take and hold. Judged from the hard carbides inside it: smaller and fewer carbides allow a keener edge.
Our ratings, inferred from published lab tests and composition.
Our edge-retention grade is a kitchen rating. It weighs the hardness each steel is sold at, which keeps a thin edge from rolling, twice as heavily as lab wear tests, and the final grade is our judgment from selling and sharpening these knives for over a decade. Lab card-cutting tests measure abrasive wear only, so they can rank carbon steels lower. Tap ? for the lab figure.
SLD
SLD鋼
Semi-stainless · Hitachi Metals (now Proterial)
Proterial cold work die steel near D2: 1.5% carbon, 12% chromium, hardening hardness over 58 HRC. Good edge life.
Read moreSanmai - Stainless Damascus Clad
三枚ダマスカス
3 layers · damascus clad
Hard core between stainless damascus layers, bare at the edge. Thinning wears the pattern.
Read more
Kurouchi
Black forge scale
Dark forge scale left on the upper blade. The bevel and edge still need care.
Read more
Octagonal Birch Burl with Spacer
Octagonal WA
Stabilised birch burl, eight-sided, with a spacer. Resin-stabilised wood resists water.










